MeshWorkflowControl

class ansys.mechanical.stubs.v251.Ansys.ACT.Automation.Mechanical.MeshWorkflowControl(internalObject: Any)

Bases: object

Object that wraps IDSEngineeringModelControl.

Overview

Methods

Activate	Activate the current object.
AddFigure	Creates a new child Figure.
AddImage	Creates a new child Image.
CanCheckPublicStateCallbackForIM	CanCheckPublicStateCallbackForIM method.
CanShowPublishStateIM	CanShowPublishStateIM method.
ControlPropertyNameToDispIDMap	ControlPropertyNameToDispIDMap method.
ConvertControl	Converts the control to a ExternalPartEnclosure
CopyControlInternalizedFileContentToClipboard	CopyControlInternalizedFileContentToClipboard method.
CopyControlInternalizedFilePathToClipboard	CopyControlInternalizedFilePathToClipboard method.
CopyTo	Copies all visible properties from this object to another.
CreateObjRef	CreateObjRef method.
CreateParameter	Creates a new parameter for a Property.
Delete	Run the Delete action.
Duplicate	Creates a copy of the current DataModelObject.
Equals	Equals method.
GetAPIName	Property name bound to dispId.
GetAllProperties	GetAllProperties method.
GetChildren	Gets the list of children, filtered by type.
GetControlPointElementSizes	Gets the Control Point Element Sizes for the specified axis.
GetControlPointIndices	Gets the Control Point Indices for the specified axis.
GetControlPointPositions	Gets the Control Point Positions for the specified axis.
GetControlPointRatios	Gets the Control Point Ratios for the specified axis.
GetDetailsView	GetDetailsView method.
GetDomainBrowserAvailableMorphFieldPatterns	GetDomainBrowserAvailableMorphFieldPatterns method.
GetDomainBrowserAvailableScopes	GetDomainBrowserAvailableScopes method.
GetDomainBrowserAvailableSizeFieldPatterns	GetDomainBrowserAvailableSizeFieldPatterns method.
GetEnumName	Enum name bound to value
GetHashCode	GetHashCode method.
GetIconFile	GetIconFile method.
GetLifetimeService	GetLifetimeService method.
GetMeshSpacingType	Gets the Mesh Spacing Type for the specified axis.
GetObjectData	GetObjectData method.
GetParameter	Gets the parameter corresponding to the given property.
GetPath	GetPath method.
GetPropertyName	GetPropertyName method.
GetPropertyValue	GetPropertyValue method.
GetPropertyWorksheetInfo	GetPropertyWorksheetInfo method.
GetType	GetType method.
GetUnpublishedList	GetUnpublishedList method.
GetVisibleProperties	GetVisibleProperties method.
GetVisiblePropertyNames	GetVisiblePropertyNames method.
GroupAllSimilarChildren	Run the GroupAllSimilarChildren action.
GroupSimilarObjects	Run the GroupSimilarObjects action.
InitializeLifetimeService	InitializeLifetimeService method.
IsPropertyEditable	IsPropertyEditable method.
IsPropertyVisible	IsPropertyVisible method.
PropertyByAPIName	Get a property by its API name.
PropertyById	PropertyById method.
PropertyByName	Get a property by its unique name.
PropertyTypeInfo	PropertyTypeInfo method.
PublishIMProp	PublishIMProp method.
RemoveParameter	Removes the parameter from the parameter set corresponding to the given property.
RenameBasedOnType	Renames applying the default name based on type.
SetControlPointElementSizes	SetControlPointElementSizes method.
SetControlPointIndices	SetControlPointIndices method.
SetControlPointPositions	SetControlPointPositions method.
SetControlPointRatios	SetControlPointRatios method.
SetMeshSpacingType	Sets the Mesh Spacing Type for the specified axis.
SetPropertyValue	SetPropertyValue method.
SetPublish	SetPublish method.
SetScopeMethodAndPattern	SetScopeMethodAndPattern method.
SetUnpublish	SetUnpublish method.
ToString	ToString method.

Properties

AddUniqueLabelPerPoint	Gets or sets whether to apply a unique label name to each added prescribed point. Uniqueness is enforced by appending a numbering suffix to the label name.
AppendData	Gets or sets whether to append the mesh data being read to the current PrimeMesh model or to clear the model content before the mesh data is being read. The default value is false.
ApplySemistructuredPattern	Gets or sets whether to apply Semistructured Pattern mapped meshing.
AttachedRefs	AttachedRefs property.
AutoCollapseShortEdges	Gets or sets whether to collapse edges below the specified tolerance. Feature edges and Protected edges are not collapsed.
AutoDeleteInteriorNodes	Gets or sets whether to delete interior nodes from scoped topology.
AutoPartialDefeature	Gets or sets whether to partially remove thin faces and sharp angles within provided tolerances, such that only topology impacting mesh quality is removed.
AutoPinchFaces	Gets or sets whether to remove small features from topology to improve mesh quality.
AutoQuad_AllowCurvedTopoFaces	Gets or sets whether to allow curved topo faces when detecting and treating holes.
AutoQuad_FragmentedEdgeTolerance	Gets or sets the edge tolerance for non circular holes with round corners in order to remove the short edge and hotspots when treating holes and features.
AutoQuad_HoleOffsetPercentage	Gets or sets the hole offset percentage to be used with mesh size when generating quad layers.
AutoQuad_MeshSize	Gets or sets the maximum size for the mesh.
AutoQuad_SplitTopoEdgesAtApexPoint	Gets or sets whether to split topo edges at their apex point when repairing topology.
AutoQuad_ThinStripesTolerance	Gets or sets the maximum thin stripe width to be used when defeaturing topology.
AutoQuad_ZoneThickness	Gets or sets the Zone Thickness to be used when converting an all quad mesh to splines.
AutoRemoveSharpAngleFaces	Gets or sets whether to remove sharp angle faces below the specified angle tolerance by merging them to the neighboring faces.
AutoRemoveThinFaces	Gets or sets whether to remove thin faces by merging them with the neighboring faces.
AutoRepairTopoEdgesOfTopoFaces	Gets or sets whether to prevent the collapse and defeature of thin or short topologies, and allow the creation of a coarse mesh while keeping topology as-is.
AutoSuppressInteriorEdges	Gets or sets whether to suppress interior edges of scoped faces.
AutomaticExternalScope	Gets or sets whether to define programmatically the external scoping method and pattern for the external enclosure. The default value is false.
BaseFaceLabel	Defines the label to be used for the base face.
BaseFaceScopeDefinition	Gets or sets the type of scope definition for the base face scoping. Default: Value
BaseFaceScopeMethod	Gets or sets the scoping method for the base face scoping. Default: Label.
BaseFaceScopeOutcome	Gets or sets the scope outcome from a previous operation. Applicable only if scope is defined by outcome.
BaseFaceScopePattern	Gets or sets the part, zone or label name pattern that defines the scope. Applicable only if scope is defined by value.
BiasingIntensity	Gets or sets the BiasingIntensity.
BiasingModality	Gets or sets the BiasingModality.
CaptureInternalFeatures	Gets or sets the CaptureInternalFeatures.
CenterPlaneNormalOffset	It defines the desired offset of the plane of the hemisphere from the model.
CenterPosition	It is defined by “Centered”, “Minimal”, and “User Defined”.
Children	Gets the list of children.
ClsId	ClsId property.
ConformalMeshOnContactSurfaces	Gets or sets whether to make the contact boundaries of the input bodies conformal. The default value is true.
ConnectIntersectionType	Gets or sets the connect intersection type. The default value is AllToAll.
ConnectionSize	Gets or sets the edge mesh size used to check the connection.
ConnectionTolerance	Gets or sets the maximum gap for the connection.
ConstantHeight	Height of a single layer of mesh elements.
ConsumeAttachments
ControlDataDefinition	This property is used to define if the control data is defined by value or by settings.
ControlDescription	ControlDescription property.
ControlDescriptionJson	ControlDescriptionJson property.
ControlScopeDefinition	It is defined by value or outcome.
ControlScopeMethod	The method can be label/zone/part.
ControlScopeOutcome	Gets or sets the ControlScopeOutcome.
ControlScopePattern	Gets or sets the ControlScopePattern.
ControlString	Gets the ControlString.
ControlType	Returns the type of the control.
ControlTypeInformation	ControlTypeInformation property.
ControlTypeInformationJson	ControlTypeInformationJson property.
CoordinateSystem	Gets or sets the Coordinate System object used to define the material point location.
CoordinatesDefinition	Gets or sets the location coordinates definition type. The default value is Location.
CoplanarAngleTolerance	Gets or sets the angle below which the faces are considered coplanar.
CreateAssemblyComponent	Gets or sets the CreateAssemblyComponent.
CreateFaceZone	Gets or sets whether to create a new face zone.
CreateGeometry	Gets or sets the CreateGeometry.
CreateQuadraticElements	Gets or sets whether to create quadratic elements. The default value is false.
CreateQuads	This property is used to define the name of the size field to apply to the meshing operation.
CreateSolidComponent	Gets or sets the CreateSolidComponent.
DataModelObjectCategory	Gets the current DataModelObject's category.
DecompositionType	Specifies the decomposition type used by the MultiZone mesher.
DefaultOffsetSize	Defines size of the offset layers to be used during the stack base operation.
DefeatureTolerance	Gets or sets the defeature tolerance applied during meshing.
DefeatureToleranceDefineBy	Specifies how the Defeature Tolerance is defined for the MultiZone mesher.
DeleteEmptyVolumes	This property is used to enable or disable the automatic deletion of empty topo volumes during mesh to topology conversion. The default value is false.
DeleteInputScope	Gets or sets whether to delete of input scope after wrapping. The default value is false.
DeleteMeshVolumes	Gets or sets the DeleteMeshVolumes.
DeleteZonePropertiesPropertyExpression	Gets or sets the DeleteZonePropertiesPropertyExpression.
DeltaX	Gets or sets the DeltaX.
DeltaY	Gets or sets the DeltaY.
DeltaZ	Gets or sets the DeltaZ.
DihedralAngle	The dihedral angle is the angle between the normal vectors of two element faces.
DirectionX	Defines x component of stacking direction to be used in stacker steps.
DirectionY	Defines y component of stacking direction to be used in stacker steps.
DirectionZ	Defines z component of stacking direction to be used in stacker steps.
DirectoryName	Gets or sets the DirectoryName.
Distance	Gets or sets the Distance.
EdgeBiasingDefineBy	Specifies how the scoped edges meshing size is defined.
EdgeBiasingFactor	Gets or sets the MultiZone Mesher edge sizing biasing factor.
EdgeBiasingType	Specifies the type of biasing to apply along the scoped edges.
EdgeCleanup	Gets or sets the EdgeCleanup.
EdgeLabelName	This property is used to rename the default edge label name generated during execution of step.
ElementSize	Define element size to achieve desired mesh results. User can achieve coarse, medium, or fine mesh by varying this value.
ElementsPerGap	Gets or sets the minimum number of element layers to be generated per gap for the Proximity Sizing control. The default values is 3.
EnableCheckpoint	Flag whether to enable a checkpoint or not. The default value is false.
EnableSmoothing	Gets or sets the EnableSmoothing.
ExcludeEnclosure	Gets or sets whether to exclude the enclosure from the wrapper scope . The default value is false.
ExcludeScopeDefinition	Gets or sets the type of scope definition for the Hole Patching exclusion scoping. Default: Value
ExcludeScopeMethod	Gets or sets the scoping method for the Hole Patching exclusion scoping. Default: Label.
ExcludeScopeOutcome	Gets or sets the scope outcome from a previous operation for the Hole Patching exclusion scoping. Applicable only if scope is defined by outcome.
ExcludeScopePattern	Gets or sets the part, zone or label name pattern for the Hole Patching exclusion scoping. Applicable only if scope is defined by value.
ExternalLabelName	This property is used to rename the default external label name generated during execution of step.
ExternalScopeDefinition	It is defined by value or outcome depending on if the External scope is defined manual by the user or defined based on a previous outcome.
ExternalScopeMethod	The method can be label/zone/part and it is applied to external region of enclosure.
ExternalScopeOutcome	If the InnerScopeDefinition is set to Outcome, then this property is visible. It defines the previous step outcome. This way we input the results of a previous step to the current step. The input applies to inner region of enclosure.
ExternalScopePattern	The value can be a name of a region or a predefined patterns to select multiple region names.
FaceZoneByPart	Gets or sets whether to define an independent face zone for each input part.
FaceZoneName	This property is used to define the name of the default face zone name generated during execution of step.
FeatureAngle	Gets or sets the angle not to be exceeded when performing repairs. Must be greater than 0 and less than or equal to 180 degrees.
FeatureSize	Gets or sets the FeatureSize.
FieldName	Gets or sets the FieldName.
Figures	Gets the list of associated figures.
FileFilter	Gets or sets the FileFilter.
Filename	Assign full path to the filename would like to Import/Export.
Filenames	Assign paths with '|' seperator to this property to read multiple files, pass without seperator if single file.
FirstLayerAspectRatio	Gets or sets the FirstLayerAspectRatio.
FirstLayerHeight	Gets or sets the FirstLayerHeight.
FixedScopeDefinition	It is defined by value or outcome.
FixedScopeMethod	The method can be label/zone/part.
FixedScopeOutcome	Gets or sets the FixedScopeOutcome.
FixedScopePattern	Gets or sets the FixedScopePattern.
FreeEdgesAsFixed	Gets or sets the FreeEdgesAsFixed.
FreeEdgesLabelName	Gets or sets the FreeEdgesLabelName.
FreeFaceMeshType	Specifies the type of elements for the MultiZone mesher free face mesh.
GapTolerance	Gets or sets the GapTolerance.
GeometryFidelity	Gets or sets the GeometryFidelity.
GroupVolumes	Gets or sets the GroupVolumes.
GroupingFolder	GroupingFolder property.
GrowthRate	Gradient of element size as each layer grows.
HemisphereCenterModality	This property is used to define the rule for the computation of the center of the hemispherical enclosure.
HemisphereOrientationModality	This property is used to define the rule for the computation of the orientation of the hemispherical enclosure.
HexcoreTetLayerRelWidth	Gets or sets the HexcoreTetLayerRelWidth.
HorizontalScopeOutcome	Gets or sets the HorizontalScopeOutcome.
HorizontalScopePattern	Gets or sets the HorizontalScopePattern.
IconName	IconName property.
IgnoreOrientation	Gets or sets whether to ignore the face normal orientation while calculating the proximity for the Proximity Sizing control. The default value is False.
IgnoreSelfProximity	Gets or sets whether to ignore the proximity between two faces from the same face zone while calculating the proximity for the Proximity Sizing control. The default value is True.
IgnoreSolidNames	Gets or sets the IgnoreSolidNames.
Images	Gets the list of associated images.
ImportSourceType	Gets or sets the ImportSourceType.
InflationGrowthRate	Gets or sets gradient of layer height.
InflationInitialHeight	Gets or sets the height of the first inflation layer.
InflationNumberOfLayers	Gets or sets the number of inflation layers.
InnerScopeDefinition	It is defined by value or outcome depending on if the Inner scope is defined manually by the user or defined based on a previous outcome.
InnerScopeMethod	The method can be label/zone/part and it is applied to inner region of enclosure.
InnerScopeOutcome	If the InnerScopeDefinition is set to Outcome, then this property is visible. It defines the previous step outcome. This way we input the results of a previous step to the current step. The input applies to inner region of enclosure.
InnerScopePattern	The value can be a name of a region or a predefined patterns to select multiple region names.
InputMeshScopeDefinition
InputMeshScopeMethod
InputMeshScopeOutcome
InputMeshScopePattern
InternalLabelName	This property is used to rename the default Internal label name generated during execution of step.
InternalObject	Gets the internal object. For advanced usage only.
IntersectingTopoFaceTolerance	Gets or sets the minimum angle used in finding thin stripes with advanced topology diagnostics.
LabelCreationExpression	Gets or sets the expression set algebra expression used in a LabelCreationByExpression control.
LabelCreationExpressionSymbol	Gets or sets the expression symbol associated to entities identified by a label creation control. These symbols can be referenced in a LabelCreationByExpression control to create labels based on expressions. Valid symbols do not contain whitespaces or any of the following characters “&, |, ^, !, (, )”.
LabelName	This property is used to rename the default label name generated during execution of step.
LastLayerAspectRatio	Gets or sets the LastLayerAspectRatio.
LateralDefeatureTolerance	Defines defeature tolerance to be used along the lateral direction of stacking.
LocalRemesh	Gets or sets the LocalRemesh.
Material	Gets or sets the Material.
MaterialName	Gets or sets the Material Name.
MaterialPointDefinition	Gets or sets the material point definition type.
MaterialPointType	It defines the type of material point, it can be “Include” or “Exclude”.
MaxEdgeLength	Gets or sets the MaxEdgeLength.
MaxHoleSize	Gets or sets the maximum size of holes to be considered for Wrapper Leak Prevention and Hole Patching.
MaxIterations	Gets or sets the MaxIterations .
MaxSize	Gets or sets the maximum size to be used for the volumetric size field sizing computation in the Proximity Sizing and Curvature Sizing controls. This is a length value.
MergeNodesTolerance	Defines the tolerance within which nodes are to be merged.
MergeOverlappingFaces	Gets or sets whether to merge overlapping faces after connect. The default value is false.
MeshEntityType	Gets or sets the target mesh entity type. The default value is Face.
MeshFlowControl	This property gives control over the flow of mesh during surface mesh generation. The supported modes are None, and Global Cartesian.
MeshedVolumeLabelSuffix	Gets or sets the suffix to be used when defining labels scoped to volumes meshed by the MultiZone mesher.
MinSize	Gets or sets the minimum size to be used for the volumetric size field sizing computation in the Proximity Sizing and Curvature Sizing controls. This is a length value.
MinimalNumberOfVolumetricLayers	It determines the minimal number of layers of volume elements to be created around the scoped body.
MinimalRadius	It defines the desired minimal radius of the spherical enclosure.
MorphFieldDefinition
MorphFieldOutcome	Gets the MorphFieldOutcome.
MorphRecordingName	This property is used to define the name for matching the morphing recording to apply to the meshing operation.
MorphSolverModality	Gets or sets the MorphSolverModality.
MorphableScopeDefinition	It is defined by value or outcome.
MorphableScopeMethod	The method can be label/zone/part.
MorphableScopeOutcome	Gets or sets the MorphableScopeOutcome.
MorphableScopePattern	Gets or sets the MorphableScopePattern.
MultiEdgesLabelName	Gets or sets the MultiEdgesLabelName.
Name	Name property.
Names	Gets or sets the Names.
NormalAngle	Gets or sets the maximum allowed normal angle between neighboring elements when computing curvature for the Curvature Sizing control. This value must be between 0 and 180 degrees (0 to π) and defaults to 18 degrees.
NormalTolerance	Gets or sets the NormalTolerance.
NumberOfAttempts	Number of attempts for mesh convergence.
NumberOfDivisions	Gets or sets the number of divisions for the scoped edges.
NumberOfLayers	Number of layers of mesh elements.
NumberOfRadialDivisions	Gets or sets the number of radial divisions to apply to scoped faces having two concentric boundary loops.
NumberOfRings	Gets or sets the NumberOfRings.
NumberOfThreads	Gets or sets the NumberOfThreads.
NumberOfVolumetricLayers	Allows user to input number of volumetric layers of the enclosure.
ObjectId	ObjectId property.
ObjectState	ObjectState property.
ObjectTags	ObjectTags property.
OffsetDistance	Gets or sets the OffsetDistance.
OffsetFileName	Gets or sets the OffsetFileName.
OffsetType	Gets or sets the OffsetType.
OriginX	Defines x coordinate of origin (location of base face) in the base face creation step.
OriginY	Defines y coordinate of origin (location of base face) in the base face creation step.
OriginZ	Defines z coordinate of origin (location of base face) in the base face creation step.
OverlapTolerance	Gets or sets the OverlapTolerance.
OverlappingTopoFaceTolerance	Gets or sets the tolerance for the minimum overlap distance used in finding overlapping topology faces with advanced topology diagnostics.
Parent	Parent property.
PartName	This property allows user to rename the default part name generated during wrap operation.
PercentageIncrement	The number of volumetric Layers determines the number of layers. This property decides whether all the layers are an equal size (default 0.0) or they should gradually increase the size of volume element than previous element.
PercentageSmoothing	Gets or sets the PercentageSmoothing.
PinchTolerance	Gets or sets the largest tolerance to be used when removing small features.
PrescribedPointsFileName	Gets or sets the path to the file containing the prescribed points locations. The data must be in csv format.
PreserveBoundary	Gets or sets whether to preserve the boundary or not. If true, adding a prescribed point which causes a deformation of the volume boundary will result in a failure.
PreserveBoundaryLayers	Gets or sets the PreserveBoundaryLayers.
ProjectOnGeometry	Gets or sets the ProjectOnGeometry.
ProjectSideFaces	Gets or sets whether to project the side faces after the extrusion.
Properties	Gets the list of properties for this object.
PropertyName	Gets or sets the PropertyName.
PropertyValue	Gets or sets the PropertyValue.
ProximityRadius	Gets or sets the radius for the proximity based search.
QuadBoundaryLayerFaceScopeDefinition	Gets or sets the type of scope definition for the quad boundary layer face scoping. Default: Value
QuadBoundaryLayerFaceScopeMethod	Gets or sets the scoping method for the quad boundary layer face scoping. Default: Label.
QuadBoundaryLayerFaceScopeOutcome	Gets or sets the scope outcome from a previous operation. Applicable only if scope is defined by outcome.
QuadBoundaryLayerFaceScopePattern	Gets or sets the part, zone or label name pattern that defines the scope. Applicable only if scope is defined by value.
QuadBoundaryLayerFirstLayerHeight	Gets or sets the height of the first quad layer.
QuadBoundaryLayerGrowthRate	Gets or sets the ratio of heights between adjacent quad layers.
QuadBoundaryLayerNumberOfDivisions	Gets or sets the number of divisions on the washer boundary from where the quad layers are grown.
QuadBoundaryLayerNumberOfLayers	Gets or sets the number of quad layers on the washer boundary.
RecomputeClosedVolumes	Gets or sets whether to recompute closed volumes after the operation.
ReferenceFaceScopeDefinition
ReferenceFaceScopeScopeMethod
ReferenceFaceScopeScopeOutcome
ReferenceFaceScopeScopePattern
RegionType	It is defined by Material Point or External.
Remesh	Gets or sets whether to allow the remesh of already meshed volumes. The default value is false.
RepairModel	Gets or sets whether to repair the PrimeMesh model after the reading operation is executed. The default value is false.
RepairTolerance	Gets or sets the tolerance value to be used to reduce variability of output topology, prevent the collapse and defeature of thin or short topologies, and allow the creation of a coarse mesh while keeping topology as-is.
RestrictBoundaryNodes	Gets or sets whether to restrict the boundary nodes displacement. The default value is true.
RetainMeshedTopoFaces	Gets or sets the RetainMeshedTopoFaces.
RetryWithGeometry	Gets or sets the RetryWithGeometry.
ReverseDeformationFieldName	Gets or sets the ReverseDeformationFieldName.
ReverseEdgeBiasingDirection	Gets or sets whether the Multizone Mesher edge biasing direction should be reversed.
ReverseSurfaceOrientation	Reverse Surface Orientation. The default value is false.
RigidScopeDefinition	It is defined by value or outcome.
RigidScopeMethod	The method can be label/zone/part.
RigidScopeOutcome	Gets or sets the RigidScopeOutcome.
RigidScopePattern	Gets or sets the RigidScopePattern.
RotationAngle	Gets or sets the RotationAngle.
ScaleFactor	Scale Factor is used to scale shapes in different dimensions.
ScopeDefinition	It is defined by value or outcome.
ScopeMethod	The method can be label/zone/part.
ScopeOutcome	If the InnerScopeDefinition is set to Outcome, then this property is visible. It defines the previous step outcome. This way we input the results of a previous step to the current step. The input applies to inner region of enclosure.
ScopePattern	The value can be a name of a region or a predefined patterns to select multiple region names.
ScriptFilename
SeedFaceScopeDefinition	Gets or sets the type of scope definition for the seed face scoping. Default: Value
SeedFaceScopeMethod	Gets or sets the scoping method for the seed face scoping. Default: Label.
SeedFaceScopeOutcome	Gets or sets the scope outcome from a previous operation. Applicable only if scope is defined by outcome.
SeedFaceScopePattern	Gets or sets the part, zone or label name pattern that defines the scope. Applicable only if scope is defined by value.
SelfIntersectionsLabelName	Gets or sets the SelfIntersectionsLabelName.
SemistructuredPatternType	Specifies the Semistructured Pattern type used by the MultiZone Mapped Meshing control.
SharedTopologyLabelName	Gets or sets the name used as label to scope the shared topology faces which are automatically added as input mesh for MultiZone.
SharpAngle	Gets or sets the maximum angle between faces to be merged. Must be greater than 0 and less than or equal to 30 degrees.
ShortEdgeLength	Gets or sets the maximum edge length to be collapsed.
SideTolerance	Gets or sets the SideTolerance.
SizeFieldDefinition	Gets or sets how the control's size field pattern should be defined, either by “Value” or by “Outcome”. The default value is “Value”.
SizeFieldName	This property is used to define the name of the size field to apply to the meshing operation.
SizeFieldOutcome	Gets or sets the outcome to be used to define the size field pattern when SizeFieldDefinition is set to “Outcome”.
SizeFieldPattern	This property is used to define the name pattern for matching the size fields to apply to the meshing operation.
SkipInteractiveSession	Gets or sets whether to skip the interactive session on execution. The default value is false.
SmallTopoEdgesLength	Gets or sets the max edge length used in finding small topo edges with advanced topology diagnostics.
SmoothingIterations	Allows user to input number of iterations needed to achieve good mesh results.
SmoothingPreserveVolume	Gets or sets whether to enable and disable the volume preserving smoothing. If enabled, the smoothing will preserve the initial volume of the input. The default value is false.
SourceScopeDefinition	It is defined by value or outcome.
SourceScopeMethod	The method can be label/zone/part.
SourceScopeOutcome	Gets or sets the SourceScopeOutcome.
SourceScopePattern	Gets or sets the SourceScopePattern.
SourceTargetScopeDefinition
SourceTargetScopeMethod
SourceTargetScopeOutcome
SourceTargetScopePattern
SphereCenterModality	This property is used to define the rule for the computation of the center of the spherical enclosure.
StackingDefeatureTolerance	Defines defeature tolerance to be used along the stacking direction.
State	State property.
Suppressed	Gets or sets the Suppressed.
SurfaceMeshType	This property gives control over what type of elements need to be generated in the mesh. The supported surface mesh types are Triangles and Quadrilaterals.
SurfaceScopeModality	The method can be label/zone/part.
SurfaceTolerance	Gets or sets the SurfaceTolerance.
SweepingSize	Gets or sets the constant size along the sweeping direction.
TargetScopeDefinition	It is defined by value or outcome.
TargetScopeMethod	The method can be label/zone/part.
TargetScopeOutcome	Gets or sets the TargetScopeOutcome.
TargetScopePattern	Gets or sets the TargetScopePattern.
TargetSkewness	Set Limit to the skewness of an element. Higher the skewness value, expecting a better mesh result.
Thickness	Gets or sets the Thickness to be assigned to the scoped zone.
ThinFaceWidth	Gets or sets the maximum thin face width to be merged.
ThinStripesWidth	Gets or sets the max width used in finding thin stripes with advanced topology diagnostics.
TopologyConformalConnection	Gets or sets whether to preserve the topology connection for the newly created faces. The default value is false.
TriangleCountReductionMode	This property gives control over the mode/degree of triangle count reduction during surface mesh generation. The supported modes are None, Conservative and Aggressive.
TrimDistance	Gets or sets the distance for the mesh based trim.
TrimElementSelectionType	Gets or sets the trim element selection type. The default value is Outside.
TrimOperationType	Gets or sets the trim operation type. The default value is Trim.
UnitsSystem	Gets or sets the UnitsSystem.
UnoDataEDXPath	Gets or sets the UnoDataEDXPath.
VariableName	Gets or sets the VariableName.
VariableType	Gets or sets the VariableType.
VariableValue	Gets or sets the VariableValue.
VerticalDirectionX	Gets or sets the VerticalDirectionX.
VerticalDirectionY	Gets or sets the VerticalDirectionY.
VerticalDirectionZ	Gets or sets the VerticalDirectionZ.
VerticalScopeOutcome	Gets or sets the VerticalScopeOutcome.
VerticalScopePattern	Gets or sets the VerticalScopePattern.
VerticalizeTargetNormal	This property defines the target normal direction for the faces during verticalization. The available options are XPlus, YPlus, ZPlus, XMinus, YMinus, ZMinus.
VisibleProperties	Gets the list of properties that are visible for this object.
VolumeCushionPercentage	Gets or sets the VolumeCushionPercentage.
VolumeMeshType	Type of Volume elements such as Tetrahedrons and Hex.
VolumeScopeModality	The method can be label/zone/part.
VolumeZoneName	This property is used to rename the default volume zone name generated during execution of step.
WorkingDirectory	Gets or sets the WorkingDirectory.
WrapByParts	Gets or sets whether to wrap each part separately. The default value is false.
XAxis	Gets or sets the XAxis.
XCoordinate	It defines the X Coordinate.
YAxis	Gets or sets the YAxis.
YCoordinate	It defines the Y Coordinate.
ZAxis	Gets or sets the ZAxis.
ZCoordinate	It defines the Z Coordinate.
ZoneType	Gets or sets the ZoneType.

Property detail

property MeshWorkflowControl.AddUniqueLabelPerPoint: bool | None

Gets or sets whether to apply a unique label name to each added prescribed point. Uniqueness is enforced by appending a numbering suffix to the label name.

property MeshWorkflowControl.AppendData: bool | None

Gets or sets whether to append the mesh data being read to the current PrimeMesh model or to clear the model content before the mesh data is being read. The default value is false.

property MeshWorkflowControl.ApplySemistructuredPattern: bool | None

Gets or sets whether to apply Semistructured Pattern mapped meshing.

property MeshWorkflowControl.AttachedRefs: List[int] | None

AttachedRefs property.

property MeshWorkflowControl.AutoCollapseShortEdges: bool | None

Gets or sets whether to collapse edges below the specified tolerance. Feature edges and Protected edges are not collapsed.

property MeshWorkflowControl.AutoDeleteInteriorNodes: bool | None

Gets or sets whether to delete interior nodes from scoped topology.

property MeshWorkflowControl.AutoPartialDefeature: bool | None

Gets or sets whether to partially remove thin faces and sharp angles within provided tolerances, such that only topology impacting mesh quality is removed.

property MeshWorkflowControl.AutoPinchFaces: bool | None

Gets or sets whether to remove small features from topology to improve mesh quality.

property MeshWorkflowControl.AutoQuad_AllowCurvedTopoFaces: bool | None

Gets or sets whether to allow curved topo faces when detecting and treating holes.

property MeshWorkflowControl.AutoQuad_FragmentedEdgeTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the edge tolerance for non circular holes with round corners in order to remove the short edge and hotspots when treating holes and features.

property MeshWorkflowControl.AutoQuad_HoleOffsetPercentage: float | None

Gets or sets the hole offset percentage to be used with mesh size when generating quad layers.

property MeshWorkflowControl.AutoQuad_MeshSize: Ansys.Core.Units.Quantity | None

Gets or sets the maximum size for the mesh.

property MeshWorkflowControl.AutoQuad_SplitTopoEdgesAtApexPoint: bool | None

Gets or sets whether to split topo edges at their apex point when repairing topology.

property MeshWorkflowControl.AutoQuad_ThinStripesTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the maximum thin stripe width to be used when defeaturing topology.

property MeshWorkflowControl.AutoQuad_ZoneThickness: Ansys.Core.Units.Quantity | None

Gets or sets the Zone Thickness to be used when converting an all quad mesh to splines.

property MeshWorkflowControl.AutoRemoveSharpAngleFaces: bool | None

Gets or sets whether to remove sharp angle faces below the specified angle tolerance by merging them to the neighboring faces.

property MeshWorkflowControl.AutoRemoveThinFaces: bool | None

Gets or sets whether to remove thin faces by merging them with the neighboring faces.

property MeshWorkflowControl.AutoRepairTopoEdgesOfTopoFaces: bool | None

Gets or sets whether to prevent the collapse and defeature of thin or short topologies, and allow the creation of a coarse mesh while keeping topology as-is.

property MeshWorkflowControl.AutoSuppressInteriorEdges: bool | None

Gets or sets whether to suppress interior edges of scoped faces.

property MeshWorkflowControl.AutomaticExternalScope: bool | None

Gets or sets whether to define programmatically the external scoping method and pattern for the external enclosure. The default value is false.

property MeshWorkflowControl.BaseFaceLabel: str | None

Defines the label to be used for the base face.

property MeshWorkflowControl.BaseFaceScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

Gets or sets the type of scope definition for the base face scoping. Default: Value

property MeshWorkflowControl.BaseFaceScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

Gets or sets the scoping method for the base face scoping. Default: Label.

property MeshWorkflowControl.BaseFaceScopeOutcome: int | None

Gets or sets the scope outcome from a previous operation. Applicable only if scope is defined by outcome.

property MeshWorkflowControl.BaseFaceScopePattern: str | None

Gets or sets the part, zone or label name pattern that defines the scope. Applicable only if scope is defined by value.

property MeshWorkflowControl.BiasingIntensity: float | None

Gets or sets the BiasingIntensity.

property MeshWorkflowControl.BiasingModality: Ansys.Mechanical.DataModel.Enums.MeshWorkflowMorphingBiasingType | None

Gets or sets the BiasingModality.

property MeshWorkflowControl.CaptureInternalFeatures: bool | None

Gets or sets the CaptureInternalFeatures.

property MeshWorkflowControl.CenterPlaneNormalOffset: Ansys.Core.Units.Quantity | None

It defines the desired offset of the plane of the hemisphere from the model.

property MeshWorkflowControl.CenterPosition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SphereCenterDefinitionType | None

It is defined by “Centered”, “Minimal”, and “User Defined”.

property MeshWorkflowControl.Children: List[Ansys.Mechanical.DataModel.Interfaces.IDataModelObject] | None

Gets the list of children.

property MeshWorkflowControl.ClsId: int | None

ClsId property.

property MeshWorkflowControl.ConformalMeshOnContactSurfaces: bool | None

Gets or sets whether to make the contact boundaries of the input bodies conformal. The default value is true.

property MeshWorkflowControl.ConnectIntersectionType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ConnectIntersectionType | None

Gets or sets the connect intersection type. The default value is AllToAll.

property MeshWorkflowControl.ConnectionSize: Ansys.Core.Units.Quantity | None

Gets or sets the edge mesh size used to check the connection.

property MeshWorkflowControl.ConnectionTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the maximum gap for the connection.

property MeshWorkflowControl.ConstantHeight: Ansys.Core.Units.Quantity | None

Height of a single layer of mesh elements.

property MeshWorkflowControl.ConsumeAttachments: bool | None

property MeshWorkflowControl.ControlDataDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ControlDataDefinedByType | None

This property is used to define if the control data is defined by value or by settings.

property MeshWorkflowControl.ControlDescription: System.Collections.Generic.Dictionary[str, Any] | None

ControlDescription property.

property MeshWorkflowControl.ControlDescriptionJson: str | None

ControlDescriptionJson property.

property MeshWorkflowControl.ControlScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome.

property MeshWorkflowControl.ControlScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.ControlScopeOutcome: int | None

Gets or sets the ControlScopeOutcome.

property MeshWorkflowControl.ControlScopePattern: str | None

Gets or sets the ControlScopePattern.

property MeshWorkflowControl.ControlString: str | None

Gets the ControlString.

property MeshWorkflowControl.ControlType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ControlType | None

Returns the type of the control.

property MeshWorkflowControl.ControlTypeInformation: System.Collections.Generic.Dictionary[str, str] | None

ControlTypeInformation property.

property MeshWorkflowControl.ControlTypeInformationJson: str | None

ControlTypeInformationJson property.

property MeshWorkflowControl.CoordinateSystem: Ansys.ACT.Automation.Mechanical.CoordinateSystem | None

Gets or sets the Coordinate System object used to define the material point location.

property MeshWorkflowControl.CoordinatesDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.CoordinatesDefineByType | None

Gets or sets the location coordinates definition type. The default value is Location.

property MeshWorkflowControl.CoplanarAngleTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the angle below which the faces are considered coplanar.

property MeshWorkflowControl.CreateAssemblyComponent: bool | None

Gets or sets the CreateAssemblyComponent.

property MeshWorkflowControl.CreateFaceZone: bool | None

Gets or sets whether to create a new face zone.

property MeshWorkflowControl.CreateGeometry: bool | None

Gets or sets the CreateGeometry.

property MeshWorkflowControl.CreateQuadraticElements: bool | None

Gets or sets whether to create quadratic elements. The default value is false.

property MeshWorkflowControl.CreateQuads: bool | None

This property is used to define the name of the size field to apply to the meshing operation.

property MeshWorkflowControl.CreateSolidComponent: bool | None

Gets or sets the CreateSolidComponent.

property MeshWorkflowControl.DataModelObjectCategory: Ansys.Mechanical.DataModel.Enums.DataModelObjectCategory | None

Gets the current DataModelObject's category.

property MeshWorkflowControl.DecompositionType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.DecompositionType | None

Specifies the decomposition type used by the MultiZone mesher.

property MeshWorkflowControl.DefaultOffsetSize: Ansys.Core.Units.Quantity | None

Defines size of the offset layers to be used during the stack base operation.

property MeshWorkflowControl.DefeatureTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the defeature tolerance applied during meshing.

property MeshWorkflowControl.DefeatureToleranceDefineBy: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.DefeatureToleranceDefineBy | None

Specifies how the Defeature Tolerance is defined for the MultiZone mesher.

property MeshWorkflowControl.DeleteEmptyVolumes: bool | None

This property is used to enable or disable the automatic deletion of empty topo volumes during mesh to topology conversion. The default value is false.

property MeshWorkflowControl.DeleteInputScope: bool | None

Gets or sets whether to delete of input scope after wrapping. The default value is false.

property MeshWorkflowControl.DeleteMeshVolumes: bool | None

Gets or sets the DeleteMeshVolumes.

property MeshWorkflowControl.DeleteZonePropertiesPropertyExpression: str | None

Gets or sets the DeleteZonePropertiesPropertyExpression.

property MeshWorkflowControl.DeltaX: float | None

Gets or sets the DeltaX.

property MeshWorkflowControl.DeltaY: float | None

Gets or sets the DeltaY.

property MeshWorkflowControl.DeltaZ: float | None

Gets or sets the DeltaZ.

property MeshWorkflowControl.DihedralAngle: Ansys.Core.Units.Quantity | None

The dihedral angle is the angle between the normal vectors of two element faces.

property MeshWorkflowControl.DirectionX: float | None

Defines x component of stacking direction to be used in stacker steps.

property MeshWorkflowControl.DirectionY: float | None

Defines y component of stacking direction to be used in stacker steps.

property MeshWorkflowControl.DirectionZ: float | None

Defines z component of stacking direction to be used in stacker steps.

property MeshWorkflowControl.DirectoryName: str | None

Gets or sets the DirectoryName.

property MeshWorkflowControl.Distance: float | None

Gets or sets the Distance.

property MeshWorkflowControl.EdgeBiasingDefineBy: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.EdgeBiasingType | None

Specifies how the scoped edges meshing size is defined.

property MeshWorkflowControl.EdgeBiasingFactor: float | None

Gets or sets the MultiZone Mesher edge sizing biasing factor.

property MeshWorkflowControl.EdgeBiasingType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.EdgeBiasingType | None

Specifies the type of biasing to apply along the scoped edges.

property MeshWorkflowControl.EdgeCleanup: bool | None

Gets or sets the EdgeCleanup.

property MeshWorkflowControl.EdgeLabelName: str | None

This property is used to rename the default edge label name generated during execution of step.

property MeshWorkflowControl.ElementSize: Ansys.Core.Units.Quantity | None

Define element size to achieve desired mesh results. User can achieve coarse, medium, or fine mesh by varying this value.

property MeshWorkflowControl.ElementsPerGap: int | None

Gets or sets the minimum number of element layers to be generated per gap for the Proximity Sizing control. The default values is 3.

property MeshWorkflowControl.EnableCheckpoint: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.CheckpointDefinitionType | None

Flag whether to enable a checkpoint or not. The default value is false.

property MeshWorkflowControl.EnableSmoothing: bool | None

Gets or sets the EnableSmoothing.

property MeshWorkflowControl.ExcludeEnclosure: bool | None

Gets or sets whether to exclude the enclosure from the wrapper scope . The default value is false.

property MeshWorkflowControl.ExcludeScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

Gets or sets the type of scope definition for the Hole Patching exclusion scoping. Default: Value

property MeshWorkflowControl.ExcludeScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

Gets or sets the scoping method for the Hole Patching exclusion scoping. Default: Label.

property MeshWorkflowControl.ExcludeScopeOutcome: Ansys.ACT.Automation.Mechanical.MeshWorkflowOutcome | None

Gets or sets the scope outcome from a previous operation for the Hole Patching exclusion scoping. Applicable only if scope is defined by outcome.

property MeshWorkflowControl.ExcludeScopePattern: str | None

Gets or sets the part, zone or label name pattern for the Hole Patching exclusion scoping. Applicable only if scope is defined by value.

property MeshWorkflowControl.ExternalLabelName: str | None

This property is used to rename the default external label name generated during execution of step.

property MeshWorkflowControl.ExternalScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome depending on if the External scope is defined manual by the user or defined based on a previous outcome.

property MeshWorkflowControl.ExternalScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part and it is applied to external region of enclosure.

property MeshWorkflowControl.ExternalScopeOutcome: Ansys.ACT.Automation.Mechanical.MeshWorkflowOutcome | None

If the InnerScopeDefinition is set to Outcome, then this property is visible. It defines the previous step outcome. This way we input the results of a previous step to the current step. The input applies to inner region of enclosure.

property MeshWorkflowControl.ExternalScopePattern: str | None

The value can be a name of a region or a predefined patterns to select multiple region names.

property MeshWorkflowControl.FaceZoneByPart: bool | None

Gets or sets whether to define an independent face zone for each input part.

property MeshWorkflowControl.FaceZoneName: str | None

This property is used to define the name of the default face zone name generated during execution of step.

property MeshWorkflowControl.FeatureAngle: Ansys.Core.Units.Quantity | None

Gets or sets the angle not to be exceeded when performing repairs. Must be greater than 0 and less than or equal to 180 degrees.

property MeshWorkflowControl.FeatureSize: float | None

Gets or sets the FeatureSize.

property MeshWorkflowControl.FieldName: str | None

Gets or sets the FieldName.

property MeshWorkflowControl.Figures: Iterable[Ansys.ACT.Automation.Mechanical.Figure] | None

Gets the list of associated figures.

property MeshWorkflowControl.FileFilter: str | None

Gets or sets the FileFilter.

property MeshWorkflowControl.Filename: str | None

Assign full path to the filename would like to Import/Export.

property MeshWorkflowControl.Filenames: str | None

Assign paths with '|' seperator to this property to read multiple files, pass without seperator if single file.

property MeshWorkflowControl.FirstLayerAspectRatio: float | None

Gets or sets the FirstLayerAspectRatio.

property MeshWorkflowControl.FirstLayerHeight: Ansys.Core.Units.Quantity | None

Gets or sets the FirstLayerHeight.

property MeshWorkflowControl.FixedScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome.

property MeshWorkflowControl.FixedScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.FixedScopeOutcome: int | None

Gets or sets the FixedScopeOutcome.

property MeshWorkflowControl.FixedScopePattern: str | None

Gets or sets the FixedScopePattern.

property MeshWorkflowControl.FreeEdgesAsFixed: bool | None

Gets or sets the FreeEdgesAsFixed.

property MeshWorkflowControl.FreeEdgesLabelName: str | None

Gets or sets the FreeEdgesLabelName.

property MeshWorkflowControl.FreeFaceMeshType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.FreeFaceMeshType | None

Specifies the type of elements for the MultiZone mesher free face mesh.

property MeshWorkflowControl.GapTolerance: float | None

Gets or sets the GapTolerance.

property MeshWorkflowControl.GeometryFidelity: float | None

Gets or sets the GeometryFidelity.

property MeshWorkflowControl.GroupVolumes: bool | None

Gets or sets the GroupVolumes.

property MeshWorkflowControl.GroupingFolder: Ansys.Mechanical.DataModel.Interfaces.IDataModelObject | None

GroupingFolder property.

property MeshWorkflowControl.GrowthRate: float | None

Gradient of element size as each layer grows.

property MeshWorkflowControl.HemisphereCenterModality: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.HemisphereCenterDefinitionType | None

This property is used to define the rule for the computation of the center of the hemispherical enclosure.

property MeshWorkflowControl.HemisphereOrientationModality: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.HemisphereOrientationDefinitionType | None

This property is used to define the rule for the computation of the orientation of the hemispherical enclosure.

property MeshWorkflowControl.HexcoreTetLayerRelWidth: float | None

Gets or sets the HexcoreTetLayerRelWidth.

property MeshWorkflowControl.HorizontalScopeOutcome: int | None

Gets or sets the HorizontalScopeOutcome.

property MeshWorkflowControl.HorizontalScopePattern: str | None

Gets or sets the HorizontalScopePattern.

property MeshWorkflowControl.IconName: str | None

IconName property.

property MeshWorkflowControl.IgnoreOrientation: bool | None

Gets or sets whether to ignore the face normal orientation while calculating the proximity for the Proximity Sizing control. The default value is False.

property MeshWorkflowControl.IgnoreSelfProximity: bool | None

Gets or sets whether to ignore the proximity between two faces from the same face zone while calculating the proximity for the Proximity Sizing control. The default value is True.

property MeshWorkflowControl.IgnoreSolidNames: bool | None

Gets or sets the IgnoreSolidNames.

property MeshWorkflowControl.Images: Iterable[Ansys.ACT.Automation.Mechanical.Image] | None

Gets the list of associated images.

property MeshWorkflowControl.ImportSourceType: Ansys.Mechanical.DataModel.Enums.MeshWorkflowImportModalityType | None

Gets or sets the ImportSourceType.

property MeshWorkflowControl.InflationGrowthRate: float | None

Gets or sets gradient of layer height.

property MeshWorkflowControl.InflationInitialHeight: float | None

Gets or sets the height of the first inflation layer.

property MeshWorkflowControl.InflationNumberOfLayers: int | None

Gets or sets the number of inflation layers.

property MeshWorkflowControl.InnerScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome depending on if the Inner scope is defined manually by the user or defined based on a previous outcome.

property MeshWorkflowControl.InnerScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part and it is applied to inner region of enclosure.

property MeshWorkflowControl.InnerScopeOutcome: Ansys.ACT.Automation.Mechanical.MeshWorkflowOutcome | None

If the InnerScopeDefinition is set to Outcome, then this property is visible. It defines the previous step outcome. This way we input the results of a previous step to the current step. The input applies to inner region of enclosure.

property MeshWorkflowControl.InnerScopePattern: str | None

The value can be a name of a region or a predefined patterns to select multiple region names.

property MeshWorkflowControl.InputMeshScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

property MeshWorkflowControl.InputMeshScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

property MeshWorkflowControl.InputMeshScopeOutcome: int | None

property MeshWorkflowControl.InputMeshScopePattern: str | None

property MeshWorkflowControl.InternalLabelName: str | None

This property is used to rename the default Internal label name generated during execution of step.

property MeshWorkflowControl.InternalObject: Ansys.Common.Interop.DSObjectsAuto.IDSEngineeringModelControlAuto | None

Gets the internal object. For advanced usage only.

property MeshWorkflowControl.IntersectingTopoFaceTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the minimum angle used in finding thin stripes with advanced topology diagnostics.

property MeshWorkflowControl.LabelCreationExpression: str | None

Gets or sets the expression set algebra expression used in a LabelCreationByExpression control.

property MeshWorkflowControl.LabelCreationExpressionSymbol: str | None

Gets or sets the expression symbol associated to entities identified by a label creation control. These symbols can be referenced in a LabelCreationByExpression control to create labels based on expressions. Valid symbols do not contain whitespaces or any of the following characters “&, |, ^, !, (, )”.

property MeshWorkflowControl.LabelName: str | None

This property is used to rename the default label name generated during execution of step.

property MeshWorkflowControl.LastLayerAspectRatio: float | None

Gets or sets the LastLayerAspectRatio.

property MeshWorkflowControl.LateralDefeatureTolerance: Ansys.Core.Units.Quantity | None

Defines defeature tolerance to be used along the lateral direction of stacking.

property MeshWorkflowControl.LocalRemesh: bool | None

Gets or sets the LocalRemesh.

property MeshWorkflowControl.Material: str | None

Gets or sets the Material.

property MeshWorkflowControl.MaterialName: str | None

Gets or sets the Material Name.

property MeshWorkflowControl.MaterialPointDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.MaterialPointDefineByType | None

Gets or sets the material point definition type.

property MeshWorkflowControl.MaterialPointType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.MaterialPointType | None

It defines the type of material point, it can be “Include” or “Exclude”.

property MeshWorkflowControl.MaxEdgeLength: Ansys.Core.Units.Quantity | None

Gets or sets the MaxEdgeLength.

property MeshWorkflowControl.MaxHoleSize: Ansys.Core.Units.Quantity | None

Gets or sets the maximum size of holes to be considered for Wrapper Leak Prevention and Hole Patching.

property MeshWorkflowControl.MaxIterations: int | None

Gets or sets the MaxIterations .

property MeshWorkflowControl.MaxSize: Ansys.Core.Units.Quantity | None

Gets or sets the maximum size to be used for the volumetric size field sizing computation in the Proximity Sizing and Curvature Sizing controls. This is a length value.

property MeshWorkflowControl.MergeNodesTolerance: Ansys.Core.Units.Quantity | None

Defines the tolerance within which nodes are to be merged.

property MeshWorkflowControl.MergeOverlappingFaces: bool | None

Gets or sets whether to merge overlapping faces after connect. The default value is false.

property MeshWorkflowControl.MeshEntityType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.MeshEntityType | None

Gets or sets the target mesh entity type. The default value is Face.

property MeshWorkflowControl.MeshFlowControl: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.MeshFlowControl | None

This property gives control over the flow of mesh during surface mesh generation. The supported modes are None, and Global Cartesian.

property MeshWorkflowControl.MeshedVolumeLabelSuffix: str | None

Gets or sets the suffix to be used when defining labels scoped to volumes meshed by the MultiZone mesher.

property MeshWorkflowControl.MinSize: Ansys.Core.Units.Quantity | None

Gets or sets the minimum size to be used for the volumetric size field sizing computation in the Proximity Sizing and Curvature Sizing controls. This is a length value.

property MeshWorkflowControl.MinimalNumberOfVolumetricLayers: int | None

It determines the minimal number of layers of volume elements to be created around the scoped body.

property MeshWorkflowControl.MinimalRadius: Ansys.Core.Units.Quantity | None

It defines the desired minimal radius of the spherical enclosure.

property MeshWorkflowControl.MorphFieldDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

property MeshWorkflowControl.MorphFieldOutcome: int | None

Gets the MorphFieldOutcome.

property MeshWorkflowControl.MorphRecordingName: str | None

This property is used to define the name for matching the morphing recording to apply to the meshing operation.

property MeshWorkflowControl.MorphSolverModality: Ansys.Mechanical.DataModel.Enums.MeshWorkflowMorphingSolverType | None

Gets or sets the MorphSolverModality.

property MeshWorkflowControl.MorphableScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome.

property MeshWorkflowControl.MorphableScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.MorphableScopeOutcome: int | None

Gets or sets the MorphableScopeOutcome.

property MeshWorkflowControl.MorphableScopePattern: str | None

Gets or sets the MorphableScopePattern.

property MeshWorkflowControl.MultiEdgesLabelName: str | None

Gets or sets the MultiEdgesLabelName.

property MeshWorkflowControl.Name: str | None

Name property.

property MeshWorkflowControl.Names: str | None

Gets or sets the Names.

property MeshWorkflowControl.NormalAngle: Ansys.Core.Units.Quantity | None

Gets or sets the maximum allowed normal angle between neighboring elements when computing curvature for the Curvature Sizing control. This value must be between 0 and 180 degrees (0 to π) and defaults to 18 degrees.

property MeshWorkflowControl.NormalTolerance: float | None

Gets or sets the NormalTolerance.

property MeshWorkflowControl.NumberOfAttempts: int | None

Number of attempts for mesh convergence.

property MeshWorkflowControl.NumberOfDivisions: int | None

Gets or sets the number of divisions for the scoped edges.

property MeshWorkflowControl.NumberOfLayers: int | None

Number of layers of mesh elements.

property MeshWorkflowControl.NumberOfRadialDivisions: int | None

Gets or sets the number of radial divisions to apply to scoped faces having two concentric boundary loops.

property MeshWorkflowControl.NumberOfRings: int | None

Gets or sets the NumberOfRings.

property MeshWorkflowControl.NumberOfThreads: int | None

Gets or sets the NumberOfThreads.

property MeshWorkflowControl.NumberOfVolumetricLayers: int | None

Allows user to input number of volumetric layers of the enclosure.

property MeshWorkflowControl.ObjectId: int | None

ObjectId property.

property MeshWorkflowControl.ObjectState: Ansys.Mechanical.DataModel.Enums.ObjectState | None

ObjectState property.

property MeshWorkflowControl.ObjectTags: Iterable[Ansys.Mechanical.DataModel.Interfaces.IObjectTag] | None

ObjectTags property.

property MeshWorkflowControl.OffsetDistance: float | None

Gets or sets the OffsetDistance.

property MeshWorkflowControl.OffsetFileName: str | None

Gets or sets the OffsetFileName.

property MeshWorkflowControl.OffsetType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.PrismOffsetType | None

Gets or sets the OffsetType.

property MeshWorkflowControl.OriginX: Ansys.Core.Units.Quantity | None

Defines x coordinate of origin (location of base face) in the base face creation step.

property MeshWorkflowControl.OriginY: Ansys.Core.Units.Quantity | None

Defines y coordinate of origin (location of base face) in the base face creation step.

property MeshWorkflowControl.OriginZ: Ansys.Core.Units.Quantity | None

Defines z coordinate of origin (location of base face) in the base face creation step.

property MeshWorkflowControl.OverlapTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the OverlapTolerance.

property MeshWorkflowControl.OverlappingTopoFaceTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the tolerance for the minimum overlap distance used in finding overlapping topology faces with advanced topology diagnostics.

property MeshWorkflowControl.Parent: Ansys.Mechanical.DataModel.Interfaces.IDataModelObject | None

Parent property.

property MeshWorkflowControl.PartName: str | None

This property allows user to rename the default part name generated during wrap operation.

property MeshWorkflowControl.PercentageIncrement: float | None

The number of volumetric Layers determines the number of layers. This property decides whether all the layers are an equal size (default 0.0) or they should gradually increase the size of volume element than previous element.

property MeshWorkflowControl.PercentageSmoothing: int | None

Gets or sets the PercentageSmoothing.

property MeshWorkflowControl.PinchTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the largest tolerance to be used when removing small features.

property MeshWorkflowControl.PrescribedPointsFileName: str | None

Gets or sets the path to the file containing the prescribed points locations. The data must be in csv format.

property MeshWorkflowControl.PreserveBoundary: bool | None

Gets or sets whether to preserve the boundary or not. If true, adding a prescribed point which causes a deformation of the volume boundary will result in a failure.

property MeshWorkflowControl.PreserveBoundaryLayers: bool | None

Gets or sets the PreserveBoundaryLayers.

property MeshWorkflowControl.ProjectOnGeometry: bool | None

Gets or sets the ProjectOnGeometry.

property MeshWorkflowControl.ProjectSideFaces: bool | None

Gets or sets whether to project the side faces after the extrusion.

property MeshWorkflowControl.Properties: tuple[Ansys.ACT.Automation.Mechanical.Property] | None

Gets the list of properties for this object.

property MeshWorkflowControl.PropertyName: str | None

Gets or sets the PropertyName.

property MeshWorkflowControl.PropertyValue: str | None

Gets or sets the PropertyValue.

property MeshWorkflowControl.ProximityRadius: Ansys.Core.Units.Quantity | None

Gets or sets the radius for the proximity based search.

property MeshWorkflowControl.QuadBoundaryLayerFaceScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

Gets or sets the type of scope definition for the quad boundary layer face scoping. Default: Value

property MeshWorkflowControl.QuadBoundaryLayerFaceScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

Gets or sets the scoping method for the quad boundary layer face scoping. Default: Label.

property MeshWorkflowControl.QuadBoundaryLayerFaceScopeOutcome: int | None

Gets or sets the scope outcome from a previous operation. Applicable only if scope is defined by outcome.

property MeshWorkflowControl.QuadBoundaryLayerFaceScopePattern: str | None

Gets or sets the part, zone or label name pattern that defines the scope. Applicable only if scope is defined by value.

property MeshWorkflowControl.QuadBoundaryLayerFirstLayerHeight: Ansys.Core.Units.Quantity | None

Gets or sets the height of the first quad layer.

property MeshWorkflowControl.QuadBoundaryLayerGrowthRate: float | None

Gets or sets the ratio of heights between adjacent quad layers.

property MeshWorkflowControl.QuadBoundaryLayerNumberOfDivisions: int | None

Gets or sets the number of divisions on the washer boundary from where the quad layers are grown.

property MeshWorkflowControl.QuadBoundaryLayerNumberOfLayers: int | None

Gets or sets the number of quad layers on the washer boundary.

property MeshWorkflowControl.RecomputeClosedVolumes: bool | None

Gets or sets whether to recompute closed volumes after the operation.

property MeshWorkflowControl.ReferenceFaceScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

property MeshWorkflowControl.ReferenceFaceScopeScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

property MeshWorkflowControl.ReferenceFaceScopeScopeOutcome: int | None

property MeshWorkflowControl.ReferenceFaceScopeScopePattern: str | None

property MeshWorkflowControl.RegionType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.WrapperRegionType | None

It is defined by Material Point or External.

property MeshWorkflowControl.Remesh: bool | None

Gets or sets whether to allow the remesh of already meshed volumes. The default value is false.

property MeshWorkflowControl.RepairModel: bool | None

Gets or sets whether to repair the PrimeMesh model after the reading operation is executed. The default value is false.

property MeshWorkflowControl.RepairTolerance: Ansys.Core.Units.Quantity | None

Gets or sets the tolerance value to be used to reduce variability of output topology, prevent the collapse and defeature of thin or short topologies, and allow the creation of a coarse mesh while keeping topology as-is.

property MeshWorkflowControl.RestrictBoundaryNodes: bool | None

Gets or sets whether to restrict the boundary nodes displacement. The default value is true.

property MeshWorkflowControl.RetainMeshedTopoFaces: bool | None

Gets or sets the RetainMeshedTopoFaces.

property MeshWorkflowControl.RetryWithGeometry: bool | None

Gets or sets the RetryWithGeometry.

property MeshWorkflowControl.ReverseDeformationFieldName: str | None

Gets or sets the ReverseDeformationFieldName.

property MeshWorkflowControl.ReverseEdgeBiasingDirection: float | None

Gets or sets whether the Multizone Mesher edge biasing direction should be reversed.

property MeshWorkflowControl.ReverseSurfaceOrientation: bool | None

Reverse Surface Orientation. The default value is false.

property MeshWorkflowControl.RigidScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome.

property MeshWorkflowControl.RigidScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.RigidScopeOutcome: int | None

Gets or sets the RigidScopeOutcome.

property MeshWorkflowControl.RigidScopePattern: str | None

Gets or sets the RigidScopePattern.

property MeshWorkflowControl.RotationAngle: float | None

Gets or sets the RotationAngle.

property MeshWorkflowControl.ScaleFactor: float | None

Scale Factor is used to scale shapes in different dimensions.

property MeshWorkflowControl.ScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome.

property MeshWorkflowControl.ScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.ScopeOutcome: Ansys.ACT.Automation.Mechanical.MeshWorkflowOutcome | None

If the InnerScopeDefinition is set to Outcome, then this property is visible. It defines the previous step outcome. This way we input the results of a previous step to the current step. The input applies to inner region of enclosure.

property MeshWorkflowControl.ScopePattern: str | None

The value can be a name of a region or a predefined patterns to select multiple region names.

property MeshWorkflowControl.ScriptFilename: str | None

property MeshWorkflowControl.SeedFaceScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

Gets or sets the type of scope definition for the seed face scoping. Default: Value

property MeshWorkflowControl.SeedFaceScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

Gets or sets the scoping method for the seed face scoping. Default: Label.

property MeshWorkflowControl.SeedFaceScopeOutcome: int | None

Gets or sets the scope outcome from a previous operation. Applicable only if scope is defined by outcome.

property MeshWorkflowControl.SeedFaceScopePattern: str | None

Gets or sets the part, zone or label name pattern that defines the scope. Applicable only if scope is defined by value.

property MeshWorkflowControl.SelfIntersectionsLabelName: str | None

Gets or sets the SelfIntersectionsLabelName.

property MeshWorkflowControl.SemistructuredPatternType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SemistructuredPatternType | None

Specifies the Semistructured Pattern type used by the MultiZone Mapped Meshing control.

property MeshWorkflowControl.SharedTopologyLabelName: str | None

Gets or sets the name used as label to scope the shared topology faces which are automatically added as input mesh for MultiZone.

property MeshWorkflowControl.SharpAngle: Ansys.Core.Units.Quantity | None

Gets or sets the maximum angle between faces to be merged. Must be greater than 0 and less than or equal to 30 degrees.

property MeshWorkflowControl.ShortEdgeLength: Ansys.Core.Units.Quantity | None

Gets or sets the maximum edge length to be collapsed.

property MeshWorkflowControl.SideTolerance: float | None

Gets or sets the SideTolerance.

property MeshWorkflowControl.SizeFieldDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

Gets or sets how the control's size field pattern should be defined, either by “Value” or by “Outcome”. The default value is “Value”.

property MeshWorkflowControl.SizeFieldName: str | None

This property is used to define the name of the size field to apply to the meshing operation.

property MeshWorkflowControl.SizeFieldOutcome: Ansys.ACT.Automation.Mechanical.MeshWorkflowOutcome | None

Gets or sets the outcome to be used to define the size field pattern when SizeFieldDefinition is set to “Outcome”.

property MeshWorkflowControl.SizeFieldPattern: str | None

This property is used to define the name pattern for matching the size fields to apply to the meshing operation.

property MeshWorkflowControl.SkipInteractiveSession: bool | None

Gets or sets whether to skip the interactive session on execution. The default value is false.

property MeshWorkflowControl.SmallTopoEdgesLength: Ansys.Core.Units.Quantity | None

Gets or sets the max edge length used in finding small topo edges with advanced topology diagnostics.

property MeshWorkflowControl.SmoothingIterations: int | None

Allows user to input number of iterations needed to achieve good mesh results.

property MeshWorkflowControl.SmoothingPreserveVolume: bool | None

Gets or sets whether to enable and disable the volume preserving smoothing. If enabled, the smoothing will preserve the initial volume of the input. The default value is false.

property MeshWorkflowControl.SourceScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome.

property MeshWorkflowControl.SourceScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.SourceScopeOutcome: int | None

Gets or sets the SourceScopeOutcome.

property MeshWorkflowControl.SourceScopePattern: str | None

Gets or sets the SourceScopePattern.

property MeshWorkflowControl.SourceTargetScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

property MeshWorkflowControl.SourceTargetScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

property MeshWorkflowControl.SourceTargetScopeOutcome: int | None

property MeshWorkflowControl.SourceTargetScopePattern: str | None

property MeshWorkflowControl.SphereCenterModality: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SphereCenterDefinitionType | None

This property is used to define the rule for the computation of the center of the spherical enclosure.

property MeshWorkflowControl.StackingDefeatureTolerance: Ansys.Core.Units.Quantity | None

Defines defeature tolerance to be used along the stacking direction.

property MeshWorkflowControl.State: Ansys.Mechanical.DataModel.Enums.Legacy.State | None

State property.

property MeshWorkflowControl.Suppressed: bool | None

Gets or sets the Suppressed.

property MeshWorkflowControl.SurfaceMeshType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SurfaceMeshType | None

This property gives control over what type of elements need to be generated in the mesh. The supported surface mesh types are Triangles and Quadrilaterals.

property MeshWorkflowControl.SurfaceScopeModality: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.SurfaceTolerance: float | None

Gets or sets the SurfaceTolerance.

property MeshWorkflowControl.SweepingSize: Ansys.Core.Units.Quantity | None

Gets or sets the constant size along the sweeping direction.

property MeshWorkflowControl.TargetScopeDefinition: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeDefinedByType | None

It is defined by value or outcome.

property MeshWorkflowControl.TargetScopeMethod: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.TargetScopeOutcome: int | None

Gets or sets the TargetScopeOutcome.

property MeshWorkflowControl.TargetScopePattern: str | None

Gets or sets the TargetScopePattern.

property MeshWorkflowControl.TargetSkewness: float | None

Set Limit to the skewness of an element. Higher the skewness value, expecting a better mesh result.

property MeshWorkflowControl.Thickness: float | None

Gets or sets the Thickness to be assigned to the scoped zone.

property MeshWorkflowControl.ThinFaceWidth: Ansys.Core.Units.Quantity | None

Gets or sets the maximum thin face width to be merged.

property MeshWorkflowControl.ThinStripesWidth: Ansys.Core.Units.Quantity | None

Gets or sets the max width used in finding thin stripes with advanced topology diagnostics.

property MeshWorkflowControl.TopologyConformalConnection: bool | None

Gets or sets whether to preserve the topology connection for the newly created faces. The default value is false.

property MeshWorkflowControl.TriangleCountReductionMode: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.TriangleCountReductionMode | None

This property gives control over the mode/degree of triangle count reduction during surface mesh generation. The supported modes are None, Conservative and Aggressive.

property MeshWorkflowControl.TrimDistance: Ansys.Core.Units.Quantity | None

Gets or sets the distance for the mesh based trim.

property MeshWorkflowControl.TrimElementSelectionType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALETrimElementSelectionType | None

Gets or sets the trim element selection type. The default value is Outside.

property MeshWorkflowControl.TrimOperationType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALETrimOperationType | None

Gets or sets the trim operation type. The default value is Trim.

property MeshWorkflowControl.UnitsSystem: Ansys.Mechanical.DataModel.Enums.WBUnitSystemType | None

Gets or sets the UnitsSystem.

property MeshWorkflowControl.UnoDataEDXPath: str | None

Gets or sets the UnoDataEDXPath.

property MeshWorkflowControl.VariableName: str | None

Gets or sets the VariableName.

property MeshWorkflowControl.VariableType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.PythonVariableType | None

Gets or sets the VariableType.

property MeshWorkflowControl.VariableValue: str | None

Gets or sets the VariableValue.

property MeshWorkflowControl.VerticalDirectionX: float | None

Gets or sets the VerticalDirectionX.

property MeshWorkflowControl.VerticalDirectionY: float | None

Gets or sets the VerticalDirectionY.

property MeshWorkflowControl.VerticalDirectionZ: float | None

Gets or sets the VerticalDirectionZ.

property MeshWorkflowControl.VerticalScopeOutcome: int | None

Gets or sets the VerticalScopeOutcome.

property MeshWorkflowControl.VerticalScopePattern: str | None

Gets or sets the VerticalScopePattern.

property MeshWorkflowControl.VerticalizeTargetNormal: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.VerticalizeTargetNormal | None

This property defines the target normal direction for the faces during verticalization. The available options are XPlus, YPlus, ZPlus, XMinus, YMinus, ZMinus.

property MeshWorkflowControl.VisibleProperties: tuple[Ansys.ACT.Automation.Mechanical.Property] | None

Gets the list of properties that are visible for this object.

property MeshWorkflowControl.VolumeCushionPercentage: float | None

Gets or sets the VolumeCushionPercentage.

property MeshWorkflowControl.VolumeMeshType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.VolumeMeshType | None

Type of Volume elements such as Tetrahedrons and Hex.

property MeshWorkflowControl.VolumeScopeModality: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType | None

The method can be label/zone/part.

property MeshWorkflowControl.VolumeZoneName: str | None

This property is used to rename the default volume zone name generated during execution of step.

property MeshWorkflowControl.WorkingDirectory: str | None

Gets or sets the WorkingDirectory.

property MeshWorkflowControl.WrapByParts: bool | None

Gets or sets whether to wrap each part separately. The default value is false.

property MeshWorkflowControl.XAxis: float | None

Gets or sets the XAxis.

property MeshWorkflowControl.XCoordinate: Ansys.Core.Units.Quantity | None

It defines the X Coordinate.

property MeshWorkflowControl.YAxis: float | None

Gets or sets the YAxis.

property MeshWorkflowControl.YCoordinate: Ansys.Core.Units.Quantity | None

It defines the Y Coordinate.

property MeshWorkflowControl.ZAxis: float | None

Gets or sets the ZAxis.

property MeshWorkflowControl.ZCoordinate: Ansys.Core.Units.Quantity | None

It defines the Z Coordinate.

property MeshWorkflowControl.ZoneType: Ansys.Mechanical.DataModel.Enums.MeshWorkflowZoneType | None

Gets or sets the ZoneType.

Method detail

MeshWorkflowControl.Activate() → None

Activate the current object.

MeshWorkflowControl.AddFigure() → Ansys.ACT.Automation.Mechanical.Figure

Creates a new child Figure.

MeshWorkflowControl.AddImage(filePath: str) → Ansys.ACT.Automation.Mechanical.Image

Creates a new child Image.
If a filePath is provided, the image will be loaded from that file,
if not, the image will be a screen capture of the Geometry window.

MeshWorkflowControl.CanCheckPublicStateCallbackForIM() → bool

CanCheckPublicStateCallbackForIM method.

MeshWorkflowControl.CanShowPublishStateIM() → bool

CanShowPublishStateIM method.

MeshWorkflowControl.ControlPropertyNameToDispIDMap() → System.Collections.Generic.Dictionary[int, str]

ControlPropertyNameToDispIDMap method.

MeshWorkflowControl.ConvertControl(type: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ControlType) → None

Converts the control to a ExternalPartEnclosure

MeshWorkflowControl.CopyControlInternalizedFileContentToClipboard() → None

CopyControlInternalizedFileContentToClipboard method.

MeshWorkflowControl.CopyControlInternalizedFilePathToClipboard() → None

CopyControlInternalizedFilePathToClipboard method.

MeshWorkflowControl.CopyTo(other: Ansys.ACT.Automation.Mechanical.DataModelObject) → None

Copies all visible properties from this object to another.

MeshWorkflowControl.CreateObjRef(requestedType: type) → System.Runtime.Remoting.ObjRef

CreateObjRef method.

MeshWorkflowControl.CreateParameter(propName: str) → Ansys.ACT.Interfaces.Mechanical.IParameter

Creates a new parameter for a Property.

MeshWorkflowControl.Delete() → None

Run the Delete action.

MeshWorkflowControl.Duplicate() → Ansys.Mechanical.DataModel.Interfaces.IDataModelObject

Creates a copy of the current DataModelObject.

MeshWorkflowControl.Equals(other: Ansys.Mechanical.DataModel.Interfaces.IDataModelObject) → bool

Equals method.

MeshWorkflowControl.GetAPIName(dispId: int) → str

Property name bound to dispId.

MeshWorkflowControl.GetAllProperties() → List[Ansys.ACT.Automation.Mechanical.AutomationPropertyWrapper]

GetAllProperties method.

MeshWorkflowControl.GetChildren(recurses: bool, children: List[ChildrenType]) → List[ChildrenType]

Gets the list of children, filtered by type.

MeshWorkflowControl.GetControlPointElementSizes(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType, unit: str) → List[System.Nullable[float]]

Gets the Control Point Element Sizes for the specified axis.

MeshWorkflowControl.GetControlPointIndices(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType) → List[int]

Gets the Control Point Indices for the specified axis.

MeshWorkflowControl.GetControlPointPositions(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType, unit: str) → List[System.Nullable[float]]

Gets the Control Point Positions for the specified axis.

MeshWorkflowControl.GetControlPointRatios(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType) → List[System.Nullable[float]]

Gets the Control Point Ratios for the specified axis.

MeshWorkflowControl.GetDetailsView() → Ansys.ACT.Automation.Mechanical.DetailsViewData

GetDetailsView method.

MeshWorkflowControl.GetDomainBrowserAvailableMorphFieldPatterns(path: str) → List[System.Collections.Generic.Dictionary[str, Any]]

GetDomainBrowserAvailableMorphFieldPatterns method.

MeshWorkflowControl.GetDomainBrowserAvailableScopes(path: str) → List[System.Collections.Generic.Dictionary[str, Any]]

GetDomainBrowserAvailableScopes method.

MeshWorkflowControl.GetDomainBrowserAvailableSizeFieldPatterns(path: str) → List[System.Collections.Generic.Dictionary[str, Any]]

GetDomainBrowserAvailableSizeFieldPatterns method.

MeshWorkflowControl.GetEnumName(enumType: type, value: int, dispId: int) → str

Enum name bound to value

MeshWorkflowControl.GetHashCode() → int

GetHashCode method.

MeshWorkflowControl.GetIconFile() → System.Byte

GetIconFile method.

MeshWorkflowControl.GetLifetimeService() → Any

GetLifetimeService method.

MeshWorkflowControl.GetMeshSpacingType(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType) → Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEMeshSpacingType

Gets the Mesh Spacing Type for the specified axis.

MeshWorkflowControl.GetObjectData(info: System.Runtime.Serialization.SerializationInfo, context: System.Runtime.Serialization.StreamingContext) → None

GetObjectData method.

MeshWorkflowControl.GetParameter(propName: str) → Ansys.ACT.Interfaces.Mechanical.IParameter

Gets the parameter corresponding to the given property.

MeshWorkflowControl.GetPath() → str

GetPath method.

MeshWorkflowControl.GetPropertyName(dispId: int) → str

GetPropertyName method.

MeshWorkflowControl.GetPropertyValue(id: int) → str

GetPropertyValue method.

MeshWorkflowControl.GetPropertyWorksheetInfo(parentPath: str) → List[System.Collections.Generic.Dictionary[str, Any]]

GetPropertyWorksheetInfo method.

MeshWorkflowControl.GetType() → type

GetType method.

MeshWorkflowControl.GetUnpublishedList() → List[System.Collections.Generic.Dictionary[str, Any]]

GetUnpublishedList method.

MeshWorkflowControl.GetVisibleProperties() → List[System.Reflection.PropertyInfo]

GetVisibleProperties method.

MeshWorkflowControl.GetVisiblePropertyNames() → List[str]

GetVisiblePropertyNames method.

MeshWorkflowControl.GroupAllSimilarChildren() → None

Run the GroupAllSimilarChildren action.

MeshWorkflowControl.GroupSimilarObjects() → Ansys.ACT.Automation.Mechanical.TreeGroupingFolder

Run the GroupSimilarObjects action.

MeshWorkflowControl.InitializeLifetimeService() → Any

InitializeLifetimeService method.

MeshWorkflowControl.IsPropertyEditable(dispId: int) → bool

IsPropertyEditable method.

MeshWorkflowControl.IsPropertyVisible(dispId: int) → bool

IsPropertyVisible method.

MeshWorkflowControl.PropertyByAPIName(name: str) → Ansys.ACT.Automation.Mechanical.Property

Get a property by its API name.
If multiple properties have the same API Name, only the first property with that name will be returned.

MeshWorkflowControl.PropertyById(dispId: int) → Ansys.ACT.Automation.Mechanical.Property

PropertyById method.

MeshWorkflowControl.PropertyByName(name: str) → Ansys.ACT.Automation.Mechanical.Property

Get a property by its unique name.

MeshWorkflowControl.PropertyTypeInfo(property: Ansys.ACT.Automation.Mechanical.Property) → System.Collections.Generic.Dictionary[str, Any]

PropertyTypeInfo method.

MeshWorkflowControl.PublishIMProp() → None

PublishIMProp method.

MeshWorkflowControl.RemoveParameter(propName: str) → None

Removes the parameter from the parameter set corresponding to the given property.

MeshWorkflowControl.RenameBasedOnType() → None

Renames applying the default name based on type.

MeshWorkflowControl.SetControlPointElementSizes(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType, values: List[System.Nullable[float]], unit: str) → None

SetControlPointElementSizes method.

MeshWorkflowControl.SetControlPointIndices(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType, values: List[int]) → None

SetControlPointIndices method.

MeshWorkflowControl.SetControlPointPositions(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType, values: List[System.Nullable[float]], unit: str) → None

SetControlPointPositions method.

MeshWorkflowControl.SetControlPointRatios(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType, values: List[System.Nullable[float]]) → None

SetControlPointRatios method.

MeshWorkflowControl.SetMeshSpacingType(axis: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEAxisType, meshSpacingType: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.SALEMeshSpacingType) → None

Sets the Mesh Spacing Type for the specified axis.

MeshWorkflowControl.SetPropertyValue(id: int, value: str, validate: int) → None

SetPropertyValue method.

MeshWorkflowControl.SetPublish(id: int) → None

SetPublish method.

MeshWorkflowControl.SetScopeMethodAndPattern(methodId: int, method: Ansys.Mechanical.DataModel.MechanicalEnums.MeshWorkflow.ScopeType, patternId: int, pattern: str) → None

SetScopeMethodAndPattern method.

MeshWorkflowControl.SetUnpublish(id: int) → None

SetUnpublish method.

MeshWorkflowControl.ToString() → str

ToString method.